Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCWS Door Installation in Port St. Lucie: What to Know First
We install and service CWS doors for homeowners across Port St. Lucie as an independent CWS service provider, meaning we’re not a CWS subsidiary and we don’t answer to their warranty department. Most CWS door installations in our schedule run one to two days on site, with replacement parts ordered in advance so the job doesn’t stall. Pricing lands in the honest middle of the Port St. Lucie market: not the cheapest bid you’ll find, and not padded either. Call (772) 362-3326 and a live person answers, 24 hours a day.
This page is for the CWS owner who already has a door that’s binding, sagging, or leaking and wants to know exactly what’s involved before anyone puts a drill to the jamb. We’ll lay out the failure patterns we see on CWS products in St. Lucie County, what we do differently, and what the work actually costs.
How CWS Products Fail - and How We Fix Them
Here’s what we consistently find on CWS doors in Port St. Lucie, and how Dale Kessler’s crew addresses each one.
- CWS hinged entry doors binding at the latch side in summer. The coastal humidity and afternoon heat in Port St. Lucie make door slabs swell enough that the latch no longer clears. The fix is usually a combination of re-shimming the hinges, planing the strike edge, and re-weatherstripping. We don’t skip the shim step, because a door that’s been forced for two summers has already pulled the frame out of square.
- Weep-hole and sill failures on CWS sliding patio doors. CWS sill pans on older models pack with dirt and sand-pine needle debris common to lots east of US-1, and water backs up into the track. We pull the panel, clean the sill, drill and ream the weep holes to spec, and re-bed the track. The door rolls clean after that, and the water goes where it was designed to go.
- CWS French door astragals that never sealed right from the first winter. The astragal on the inactive leaf gets installed out of alignment at the factory, and the active leaf catches or lets a draft through. We re-set the astragal flush to both slabs, replace the interlocking weatherstrip, and verify the lock throw engages fully. Most owners don’t need new doors, they need this.
- Fogged insulated glass in CWS door lites. This is a seal-failure, not a door failure. The glass unit has lost its argon fill and the desiccant is saturated. We measure the exact thickness and order a replacement insulated unit that matches the original low-E coating. It’s a two-visit job: measure, then glazing. We register the new glass warranty in writing before we leave.
- Storm door closers on CWS units that snap or sag. The pneumatic closers CWS uses are decent, but salt air from the Indian River Lagoon shortens their life. When they fail, the door slams and the hinge screws start to eat the jamb. We replace the closer with a commercial-grade aftermarket unit and re-seat the hinges with longer screws into the framing, not just the jamb. The aftermarket closer is the one place we deviate from OEM, because the OEM part simply wears out faster here.
Our CWS Door Installation Process
Every CWS door job follows the same discipline, from the first call to the last sweep of the entryway.
- 1
Call and diagnosis. A live person answers at (772) 362-3326. We ask what the door is doing, when it started, and what model of CWS product is in the opening. If Dale can’t answer a technical question on the spot, a tech will.
- 2
Measure and inspect on site. A background-checked, uniformed technician arrives when we said he would. We measure the rough opening, the slab, the reveals, and the existing hardware. Twice. Dale Kessler grew up in the Tradition area of Port St. Lucie and learned at Indian River State College that measurements drive every decision that follows. Measure twice, order once, everything after that is just following through.
- 3
Parts decision. We quote OEM CWS parts when the product is under warranty or when nothing aftermarket matches the original. We quote a quality aftermarket option when the OEM part is a known weak point, like the storm door closer. Both options are written side by side on the quote, no mystery in the fine print.
- 4
The installation. We set the door, shim it square, and mount the hardware. If the opening has shifted, we correct the frame before the slab goes in rather than forcing the door to fit an out-of-true opening.
- 5
Testing and warranty registration. We operate the door fully open to fully closed, check the latch throw, the sweep contact, and the weatherstrip compression. Then we register both manufacturer warranty layers in writing and explain their durations before we pull out of the driveway. This is The Keystone Standard.
- 6
Cleanup and follow-through. We sweep, we remove the old door and packaging, and we walk you through what was done. Most CWS door installations are completed in a single visit.
What CWS Door Installation Costs in Port St. Lucie
Straight numbers, no vague ranges designed to hold you on the phone. Here’s what homeowners in Port St. Lucie are paying for CWS door work in our schedule.
- Rebuild and re-hang a CWS entry door: $380 to $750, depending on how far the frame has drifted and whether the slab needs edge planing.
- Replace interlocking weatherstrip and astragal on a CWS French door pair: $210 to $440.
- Re-glaze a CWS door lite with a new insulated glass unit: $340 to $680, matched to the original low-E coating.
- Replace a CWS sliding patio door roller assembly and re-bed the track: $280 to $520.
- Replace a CWS storm door closer with a commercial aftermarket unit: $140 to $260.
What moves the price: the condition of the existing frame, whether parts are OEM or aftermarket, and whether the door requires glazing. We give written line-item quotes before work starts, and the price doesn’t change once the truck arrives. Call (772) 362-3326 for your free estimate.
Why Port St. Lucie Homeowners Call TruePane Windows & Doors for CWS Work
We’ve been serving St. Lucie County since 2008 through a craft tradition that started long before TruePane Windows & Doors was founded in 2008. Dale Kessler runs this company as a second-generation glazier, not as a franchise manager reading from a corporate playbook. The Done Right Promise says what it means: if the door isn’t right, we make it right, no paperwork fight and no arguing. The Keystone Standard goes further, putting both manufacturer warranty layers in your hands in writing, with durations stated, before we leave the job site.
Our technicians work on CWS products regularly, and when the best answer isn’t a CWS product at all, we can quote Andersen, Pella, or PGT side by side on paper so you can see exactly what you’re buying. The job gets done the way we’d do it in Dale’s own home, and we’ll be there when we say we will.
FAQs
No. We are an independent CWS service provider, not a CWS-authorized dealer or warranty agent. What that means in practice: we make choices based on what’s right for the door and the opening, not what the manufacturer’s warranty department would prefer. If a CWS door is under warranty, we’ll tell you what the warranty actually covers and what it doesn’t, and we’ll install to a standard that doesn’t void it.
Not when the installation is done correctly and the warranty isn’t already voided by the condition of the opening or prior repairs. Installations that rough-force a door into an out-of-square frame are the ones that void warranty coverage. We correct the frame first, which protects the product and keeps the warranty intact. Call (772) 362-3326 and we’ll look at your specific door.
Yes, we can source CWS door parts, though some series have longer lead times than others. For common wear items like weatherstrip, astragals, and closers, we can often have the part in hand within a few business days. For less common hardware, we’ll quote the lead time up front. When a quality aftermarket part will outlast the OEM, we say that too and show both options on paper.
Usually not. In Port St. Lucie, most CWS door problems we see are frame alignment, weatherstrip, closer, or roller issues that cost between $140 and $750 to fix, while a full door replacement typically runs $2,000 and up. Replacing a door because it binds is like replacing a car because the alignment is off. We’ll give you an honest repair-versus-replace answer with numbers for both. Estimates are free at (772) 362-3326.
Most CWS door installations take one to two days on site once the parts are in hand. For common parts, that means we can often be on site within a week of the initial estimate. For slower parts, we’ll tell you the truth about the wait. A live person answers our phone 24 hours a day, 7 days a week, so you’ll get the real answer when you call, not a voicemail tree.
If your CWS door is binding, leaking, sagging, or fogged, call TruePane Windows & Doors at (772) 362-3326 for a free estimate. A live person answers, we’ll be there when we say, and we’ll stand behind the work in writing.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Port St. Lucie and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.